Replacing the timing belt "Renault Megan 2" (Renault Megane II)

Date:

2019-07-16 01:20:23

Views:

1988

Rating:

1Like 0Dislike

Share:

Table of contents:

Megane of the second generation was produced with a variety of engines with the volume from half to two liters. A common feature of all powertrains is the timing with the belt. The cars were quite popular in Russia and are quite widely available on the secondary market. After buying the car, many owners are faced with the question – how and when to replace belt drive on their "Mahaneh 2".

General data

The Factory recommends replacement of the belt to drive the camshaft 115 thousand km every engine Design is such that when the belt breaks the valve meet piston, so belt replacement is better done in advance to 65-70 thousand km During operation of the machine is recommended to check the belt after about twenty thousand miles. These simple tips will help avoid lengthy and costly engine repair.

The Main difficulty when replacing the belt is the absence of labels on the parts, on which you can establish the correct position of the timing elements. The main types of engines "Mahaneh 2", common in the Russian market:

  • Petrol 1400 cubes (98 HP) 1600 (113 and 116 HP) and 2000 (150 forces);
  • 1500 diesel (86 HP).

Special tool

For setting the correct valve timing will need the locking bolt to the crankshaft and the pattern for rotation of the camshafts. Original parts have the Mot.1054 and 1496 (for motors 1600 and 1400).

Many owners of the machines make these devices yourself using the schematic drawings of attachments.

replacing the timing belt Renault Megane 2

Content to replace

Details to replace timing belt on "Reno-Megan 2" with a 1.6-liter engine:

  • Repair Kit, seat belt (a belt, two idler rollers and bolt, used to mount the main pulley).
  • Hex bolt pulley (approximately in 2016 is not supplied in the kit timing belt).
  • Caps on the camshafts.
  • Pump the coolant.
  • Sealant for installation.

A Similar set of need and to service any other engine for "Megane 2".

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

replacing the timing belt Renault Megane 2 1 6

Tools

For changing the timing belt on "Renault Megane 2" 'll need:

  • A Standard set of wrenches.
  • Extra heads 16 and 18 mm.
  • The Hexagon with a size of 5 mm.
  • A Key under “star” 5 mm.
  • The Clips (original or improvised).
  • Flat-blade Screwdriver.
  • Hydraulic Jack.
  • Jack.

The workflow

The following describes the procedure for replacing the timing belt on a Renault Megane with the engine 1.6 16 valves (the most common variant):

  • Place the vehicle on a lift or on a pit.
  • Raise the Jack the car and remove the front wheel (right) and protective plastic locker in the arch.
  • Remove the engine screen and slightly lift it with the Jack. Between Carter and the head of the Jack to lay a wooden box, because without it you can easily damage the pallet. For lifting you can use a standard mechanical or hydraulic Jack.

replacing the timing belt Renault Megane diesel 2

  • Remove the top plastic cover from the motor.
  • Remove the bolts for fixing the engine mounts to the head. There is only five bolts. Bots have different Dean, it is better to mark their mutual arrangement.
  • Remove the three bolts which support is fixed to the spar body.
  • Remove the pillow. In this case it should be gently removed through the gap between tube and body conditioning.
  • Remove the top metal casing of the belt. He recorded two nuts and three bolts. Access to one nut is possible only through the mounting hole in the wheel arch. Under the cover removed you will see the belt, two gears, and shifter.

Renault Megane 2 replacement timing belt price

  • To Remove a steel reinforcement plate between the subframe and the body.
  • Remove the V-ribbed belt assemblies.
  • Crank shaft for the pulley nut in a clockwise direction, exposing the marks on the gears of the rotation of the camshafts. To achieve directions label up, while the right label has a little to reach the groove in the casing head.
  • Fix the crankshaft with the special bolt by screwing it into the hole in the crankcase. It is located near the flywheel (below the hole for the dipstick) and closed with a threaded plug. After screwing the bolt until it stops need to crank the shaft of the arrow hours to achieve contact with the rod retainer. The piston in the first cylinder will be in their uppermost position. The location can be checked through the hole in the head, which serves to spark plugs.

Renault Megane 2 1 4 replacing the timing belt

  • To Remove the pipe feeding the air and the throttle body.
  • Remove with a screwdriver the plastic plugs in the camshaft.
  • To Insert into the grooves in the camshafts pattern-lock. The grooves should be on the same line and be located below the axis of the shafts. Lock thickness up to 5 mm should go in without effort.

Renault replacement timing belt cost

  • Unscrew the bolt and remove the pulley. Unscrew the bolt or the starter or turning ongear and holding the brakes.
  • Loosen the bottom part of the metal casing of the belt, fastened by four bolts.
  • Remove the bolt holding the tension pulley.
  • Remove the belt.
  • Drain the fluid and remove the pump, mounted on the eight bolts. To drain the antifreeze usually use the hose from the expansion tank.
  • Remove the bypass roller.
  • Coat the gasket and the mating surface of the pump and block sealer. To install the pump and tighten the bolts in a circle.
  • Install the tensioner pulley and put the belt on the sprockets. When installing, note the direction of rotation of the mechanism. Temporarily secure it with plastic ties.
  • Pull the belt the rest of the gear and put the bypass pulley. Under video do not forget to put the washer left over from the old.
  • To Rotate the Cam in the center of the tension pulley inner hex key to align the pointer with the mark on the Cam housing. Direction of rotation is indicated on the eccentric.
  • Tighten until the bolt roller. Put the bottom half of the casing and the pulley. Remove the couplers and clamps. Crank the engine for 4-8 revolutions and check the marks and grooves match the pattern.
  • Pour the fresh liquid.
  • Install all the removed parts back.

Alternative method

Another method of validating the installation phase is the application of marks on the old belt and gears. Labels applied to all points of contact of the belt and gears.

replacing the timing belt Renault Megane engine 1 6 16

Then the labels are transferred to the new belt and it is installed on the gear in accordance with labels on them. After that, the engine cranks manually several times for another stage of control.

Renault Megane 2 1 4 replacing the timing belt

Features replacement on other engines

The procedure for replacing the timing belt on "Renault Megane 2" with a 1.4-liter 16-valve engine is absolutely identical to the above procedure 1.6-liter counterpart.

And what about diesel? Replacing the timing belt on "Renault Megane 2" with a diesel engine does not have any major differences from the petrol variants. But there are some differences:

  • Belt Guard is made of plastic and is mounted on the latch and the pin that connects the halves of the casing. This pin may be driven only through the hole in the spar. It will have to povarirovat engine position, until the pin will stand in front of the hole.
  • Before removing the cover you must remove the sensor that detects the camshaft position.
  • Fixing the camshaft is a pin with a diameter of 8 mm, which is inserted into a hole in gear and hole in the head. Crankshaft with fixed stop (original number Mot1489). Stoppers petrol and diesel engine are different lengths!
  • Since the belt drives the pump fuel gear put the label in the direction of the head of a single bolt on the crankcase.

Substitutions

When performing work with their hands the cost of replacing the timing belt on "Renault Megane 2" will consist of prices of spare parts. Thus, the cost of spare parts for diesel car will be:

  • Belt Kit 7701477028 – 3200 rubles.
  • Bolt 8200367922 – 400 rubles.
  • Pump 7701473327 – 4700 rubles. Or equivalent from the company SKF article VKPC86418 cost 2,300 rubles.
  • New coolant 7711428132 GLACEOL RX (Type D) – about 2.5 thousand rubles.

The Final price of a replacement timing belt for "Renault Megane 2" will not exceed 11 thousand rubles, which is much cheaper to overhaul the motor or buying a new engine contract.


Article in other languages:

AR: https://tostpost.com/ar/cars/18424-2-ii.html

BE: https://tostpost.com/be/a-tamab-l/35277-zamena-ramyanya-grm-reno-megan-2-renault-megane-ii.html

DE: https://tostpost.com/de/autos/34943-austausch-des-zahnriemens-renault-megan-2-renault-megane-ii.html

ES: https://tostpost.com/es/coches/34793-sustituci-n-de-la-correa-dentada-renault-megan-2-renault-megane-ii.html

HI: https://tostpost.com/hi/cars/20084-2-renault-megane.html

JA: https://tostpost.com/ja/cars/18100-megan2-ii.html

KK: https://tostpost.com/kk/avtomobil-der/35565-zamena-remnya-grm-reno--megan-2-renault-megane-ii.html

PL: https://tostpost.com/pl/samochody/36678-wymiana-paska-rozrz-du-renault-megan-2-renault-megane-ii.html

PT: https://tostpost.com/pt/carros/36481-substitui-o-da-correia-dentada-renault-megan-2-renault-megane-ii.html

TR: https://tostpost.com/tr/arabalar/31994-triger-kay-n-n-de-i-tirilmesi-reno-megan-2-renault-megane-ii.html

UK: https://tostpost.com/uk/avtomob-l/35800-zam-na-remenya-grm-reno-megan-2-renault-megane-ii.html

ZH: https://tostpost.com/zh/cars/4369-2-ii.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

What antifreeze is the best and how to choose it?

What antifreeze is the best and how to choose it?

Many car owners wonder about which antifreeze is best? In order to answer it, it is necessary to study their technical characteristics. The main purpose of antifreeze is the effective cooling of the car engine and prevent boiling....

MTZ-1025: specifications, reviews. Tractor

MTZ-1025: specifications, reviews. Tractor "Belarus"

the MTZ-1025, specifications of which are presented below, produced at the Minsk tractor plant. The machine is one of the most popular modifications designed for universal use in agriculture and related fields. Like most models of...

Lineup Ford: description

Lineup Ford: description

Car manufacturer Ford is one of the most popular and in demand among customers in Russia due to the quality and reasonable price for the entire range. Let's look briefly at the lineup of Ford and main features of each car.What car...

MAZ-203 is a comfortable multi-seater three-door bus type

MAZ-203 is a comfortable multi-seater three-door bus type

Low-floor city bus MAZ-203 is produced at the Minsk automobile plant since 2006. The machine is radically different from its predecessor, model MAZ-203. The difference lies in the configuration of the lower layer of the cabin. Hav...

How to mount a car alarm? Installation with your own hands

How to mount a car alarm? Installation with your own hands

car Alarm – it is one of the most effective anti-theft vehicle systems. Modern device can provide the maximum protection to the vehicle against theft. However, for the expectations were justified, first, you need to choose a...

"Volkswagen of Amarok": owner reviews about the new German truck

the Debut of the German pickup «Volkswagen Amarok” was held in 2009 at the international motor show in Hanover. At that time, the SUV was presented under the name of “Volkswagen Pickup Concept”. A few month...