Restorative polishing of the car body. How to get rid of scratches on the body

No matter How you tried to keep the body intact, sooner or later it all the same scratches are formed. Unfortunately, this is a natural phenomenon. Of course, scratch is markedly deteriorates the appearance of the car. But there is a way to get rid of it. Comes to the aid of restorative polishing of the car body. How to make and what it is, you will learn from our today's article.

What gives?

Unlike conventional polishing, restoration has a more spectacular result. All thanks to the fact that in the course of the work the removed paint. Ordinary Polish fills its composition cracks, making the surface more smooth and uniform. But the problem is that the result is effective only until the first washing. Next to the body again appear the old scratches that had previously tried to hide. That gives restorative polishing of the car body? In addition to the brilliance and saturation of LWA, such polishing has a long lifespan. In fact, we remove a layer of varnish, which was still not burnt, smooth paint. If the task of conventional polishing – hide unwanted flaws, when the abrasive removes all visible defects. The body can be washed many times without fear that after washing again “grow” old scratches on the car. As for specific numbers, depending on the magnitude of the damage is removed 3-10 microns of lacquer. The total thickness of the paintwork on different vehicles – from 90 to 150 microns.

Pitfalls

Despite the fact that restorative polishing of the car body has a good result, it is often impossible to apply. Experts recommend this procedure not more often than every five years. It must be remembered that after each abrasive-restorative polishing removed the layer of varnish, which is not limitless. This is especially true of Japanese cars, where the smallest thickness of the paintwork. On these vehicles removed no more than three to four microns of the layer. Also in progress is a special pasta and an angle grinder with a felt tip. In contrast to the abrasive, the usual polishing of the car body can be made manually with a piece of soft cloth.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Tools

If you perform restoration polishing a car body with his hands, you need to prepare not only abrasive paste, but eccentric machine. Important point – it must be with the speed controller. This is necessary in order to preclude excessive heating of the surface and not “from scabbing" extra layer. Still, we need nozzles, felt and foam, as well as the adapter with Velcro. Note that restorative polishing of the car body is made with a frequency of rotation of the disk is not more than 2.5 thousand revs. Additionally, we need masking tape. To them we pasted contiguous body parts. This gum, glass, gaskets. Why can't I use regular stationery tape? In its structure it leaves on the body the traces of glue. To remove them is quite difficult, except with specialized degreaser. Therefore, in order not to waste time and forces in vain, only use masking tape.

Requirements

Polishing the car body is always performed indoors. It is important to exclude the sun's rays. Because of them, the paste will dry quickly and you will not achieve the desired result. Another reason why the polishing should not be carried out on the street – is the dust. Its concentration in the street is very large. So the work we do to clean the garage or in the same room.

Start to work. Sink

The quality of the result on 70% depends on how you wash the body before treatment. During the polishing, the unacceptable presence of dust, dirt and other deposits on the surface of the paint. It is best to use a high pressure washer. Pay attention to hidden holes – the joints with the bumpers, lights, arches and other elements. Carefully examining the areas behind the fenders. In the lower part of the body often sticks to the bitumen. To wash him is quite hard even under pressure. How to be in this situation? You need to buy a specialized product. It is called – cleaner of bitumen stains. Sold in the form of a spray. After application to the surface it softens the bitumen. Clean it with a piece of clean cloth. Also should be cleaned from lice and other insects. Next, the body should be thoroughly dried.

A Few words about clay

Recently, a very popular blue clay to clean the paint. It is able to absorb all the dirt that failed to clean in conventional washer and degreaser. In its structure, blue clay is a kind of antiseptic. Experts recommend to use it before each abrasive washing. Also note that this clay is disposable. If she fell on the floor, further use is not subject. The same applies to polishing wheels. If the smallest dirt on the body will be visible gossamer.

Remove coarse scratches

So, proceed directly to treatment. Take out the paste and apply it on the surface of the foam circle. Then put on the machine mode 300 rpm and evenly RUB over the surface. Then you need to wait for pastaa little dry. Then set the mode 2-2,5 thousand revs and start to RUB the Polish. Machine floating smoothly, but without delay in the same place. Otherwise, you can overheat the paint (it is pale) or to remove excess. Large areas treated in several stages. So, the hood and roof is visually divided into two parts. If you try to do everything at once may not be enough of the paste (or it will severely dry up). Periodically check the condition of the circle. If it is dark, it must be replaced. This suggests that material has incorporated dirt. Her on the LCP are small circular scratches. To completely eliminate the phenomenon of Experts recommend to handle the body of blue clay, which were discussed above.

Shine-cover

At the end of work with an abrasive start to the finish trim of the car body. To do this, once my machine and dry it. This is done in order to remove remaining particles of abrasive material from the surface, which upon re-polished can be scratched. Next, change the nozzle and using milder polishes (nonabrasive). Put on a typewriter, one thousand rpm and work in a similar way. Ensure that each new layer is laid down parallel to the previous one. Avoid excessively strong pressing – so you damage the newly restored paint. The procedure for restoring the paintwork completed. The car is ready for everyday use.

What

Now many workshops offer the services of a professional restoration polishing body. The price depends on the type and class of vehicle. So, car b-class and below can be treated for 5-7 thousand rubles. Station wagons and crossovers – 8-12 thousand. And Polish the SUVs and premium cars costs about 15 thousand. Most charge for minivans and vans. The price of polishing the body up to 20 thousand rubles (due to the large area of coverage). Workshops that work with materials such as ZM, “the Rivaks” etc.

Conclusion

So, we found than a special abrasive polishing. As you can see, this is a great way to restore the look of your car without perekruta. Buy this Polish at any store. But finding orbital sander, you may have to suffer.