Shaft Oise: repair and balancing

Date:

2019-12-29 19:20:07

Views:

442

Rating:

1Like 0Dislike

Share:

Table of contents:

Is a four-wheel drive vehicle by connecting the axles and transfer case with drive shafts. Only two of them: front and rear, the first of them consists of a splined joint and pipes with thin walls, on both sides of which are special bits with ball bearing and flexible coupling. The bearing has additional fixation in the form of a retaining ring housed in a steel base. All the basic elements are the rubber seals that reduce vibration.

shaft UAZ

What you need to know

Front drive shaft Oise has a simple design that is fixed with a special bracket, located in the lower part. But like any other detail, it requires periodic repair or replacement. PTFE vents are a weak point of the mechanism, they are subject to rapid wear, but repair them, as we know, impossible.

The Shaft of the Oise is based on three mounting points, so it is often called tri-prop. Outboard bearing, which is a core element of support requires more careful attention. He provides a retention structure, consisting of two parts stationary. So it must be periodically inspected. Are diagnosed on average every 50 thousand miles When it is replaced by a new one often sets the gimbal straight type.

repair of drive shafts UAZ

Crystals

Despite the fact that the UAZ is a sports car, most of the load falls on the rear axle. This is because the need in front-wheel drive only occurs in the case of overcoming various obstacles. Even with moderate use, it has a great operating period, and should systematically examine and eliminate breakage. It is worth noting the problems that often arise in this mechanism:

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

  • Weakening of clamps;
  • Imbalance;
  • Shaft Oise acquired the clearance between the bearing cups;
  • The failure of the spline connection;
  • Wear of the splines;
  • Increase the clearance in the spline joint.

Cross

Like any other item, the first propeller shaft yoke Oise needs to be cleaned from dirt and rust. After noting its location and finding forks. With a hammer gently pressed into the bearing cups. The retaining ring is separated from the edge and to hook standard screwdriver. Then both sides vypressovyvaetsya bearings with lock and hammer. After turning the shaft is removed the plug with the sealing element and the crossbar. It remains only to install a new part and assemble the design in the reverse order. Cross is on both rear and front camera, while the differences in its removal and installation no.

propeller shaft UAZ patriot

Spline connection

Repair of driveshafts Oise consists primarily in the replacement of worn-out frogs. When worn spline connection gimbal, as a rule, should be replaced. This malfunction can be identified by the runout of the steering wheel when you turn wheel drive and increased backlash. It is worth noting that the average period of operation of the mechanism, depending on the intensity, is 30-50 thousand km.

In some cases, you can resort to a repair. The period of use of the spline connection can be increased by welding. This method is based on the ability of the metal to expand during heating to a certain temperature and shrinkage in the cooling process. First we need to dismantle the mechanism and to disengage the splines. Part details located under the front axle, is thoroughly cleaned. The outer part of the connection overlaps several joints with a welding machine. Then, the resulting projections should be removed with sandpaper. If not, there is a possibility of violation of the balancing. The repair of driveshafts of the Oise ends, there is only To proprietati details and to put in its place.

After shrinkage of the metal backlash, as a rule, disappears. If everything remained as before, you need to buy a new device.

cross cardan shaft UAZ

Shaft Oise: balancing

This procedure is an essential step of installation of the cardan on each car of this brand. It maintains the balance of all elements. About her improper conduct quickly enough will be known by the presence of extraneous noise, increased vibration and the occurrence of backlash in the details. To avoid repairs, which in this case may be required sooner than 10 thousand km, should be balanced, regardless of the degree of interference in the system. It should be noted that this procedure is carried out on a HUNDRED.

Lubrication of the main structural elements is of particular importance. This procedure should be performed regularly, especially as it is for any motorist. It is enough to dial “lithol-24” in special technical the syringe and extrude the part in the driveshaft. UAZ “Patriot” does not require disassembly of the mechanism, as long as sufficient access thevatican.


Article in other languages:

AR: https://tostpost.com/ar/cars/20448-shaft-oise-repair-and-balancing.html

BE: https://tostpost.com/be/a-tamab-l/38105-val-kardanny-uaza-ramont-balans-ro-ka.html

DE: https://tostpost.com/de/autos/37710-die-kardanwelle-oise-reparatur-und-auswuchten.html

ES: https://tostpost.com/es/coches/37493-eje-de-toma-de-fuerza-de-la-uaz-la-reparaci-n-y-el-equilibrio-de.html

HI: https://tostpost.com/hi/cars/21092-oise.html

JA: https://tostpost.com/ja/cars/20097-shaft-oise-repair-and-balancing.html

KK: https://tostpost.com/kk/avtomobil-der/37605-val-kardany-uaz-zh-ndeu-zh-ne-te-geru.html

PL: https://tostpost.com/pl/samochody/36721-wa-kardana-uaza-naprawa-i-wywa-anie.html

PT: https://tostpost.com/pt/carros/36942-eixo-cardan-oise-repara-o-e-balanceamento-de.html

TR: https://tostpost.com/tr/arabalar/34965-aft-aft-n-oise-onar-m-ve-dengeleme.html

UK: https://tostpost.com/uk/avtomob-l/37377-val-kardanniy-uaz-remont-balansuvannya.html

ZH: https://tostpost.com/zh/cars/18270-shaft-oise-repair-and-balancing.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

Pendant

Pendant "Next" ("Gazelle"): photo, repair

"the Gazelle" "Next" (pendant) is mounted with the thrust rings. Most experts say that a specified modification in the first place quality spring. It is also worth to note the strong bridge. The brackets are at the top of the rod....

Front axle MTZ-82: circuit, device and repair (photo)

Front axle MTZ-82: circuit, device and repair (photo)

Front axle of the tractor MTZ-82 is manufactured with a leading reducer. The model fitted the strip and there are metal stops. Most experts believe that the device has a solid rack. Disks have modifications apply gear type. In ord...

The scooter for disabled and elderly people: tips for choosing

The scooter for disabled and elderly people: tips for choosing

Scooter for disabled is a safe and convenient mode of transport, which can enhance the ability of movement. Control it as simple as possible, since the wheel is installed in any position, comfortable movement is provided by an inf...

Wiring diagram for DRL from the generator or via a relay. How to connect daytime running lights with your hands?

Wiring diagram for DRL from the generator or via a relay. How to connect daytime running lights with your hands?

DRL (daytime running lights) in the vehicle can be connected through the generator or relay. In this case, it is necessary to take into account lamp power. Standard scheme involves the use of a extender for the four outputs. The i...

Car

Car "Lexus-450": description, specifications, reviews

“Lexus-450” exists in two different versions. First – a diesel car, which is still in the name of the prefix LX. The second is a hybrid. Each of these models in their own good and unique, but also enjoys unquesti...