The carburetor DAAZ-4178: specifications and adjustment

Date:

2019-12-04 02:20:17

Views:

964

Rating:

1Like 0Dislike

Share:

Table of contents:

For over 100 years, the carb is used on most gasoline cars. This device is in the preparation of a mixture of air and fuel vapor, which gets into the combustion chamber. Consider how the carburetor DAAZ-4178, learn its specifications and learn how to regulate its work.

DAAZ for cars UAZ and "Volga"

Many owners of the UAZ vehicles, and also "Volga" with a 402-m motor interested in issues of selection of carburetors for their cars. If an analysis of all available solutions on the market, it is best for these engines fit the device from Dmitrovsky aggregate plant.

carburetor DAAZ 4178

The Carburetor DAAZ-4178 from motorists is considered to be a very popular model. It allows to significantly improve the dynamics of the engine, and when properly configured, leads to a reduced fuel consumption.

Device carb

These units are designed to produce high quality fuel-air mixture. Then the unit feeds it into the combustion chamber. The ratio of the fuel mixture is directly proportional to the amount of air that passes through the device.

Line 4178 is a triple-emulsion system. In General, the entire line, and the carburetor DAAZ-4178-1107010-30 including, has the same device. In these carburetors applied all effective and well-proven technology. Here it is possible to note the presence of a more balanced float chamber, a system of consistent of opening valves and other technologies.

The Device is assembled from standard components and assemblies and is virtually indistinguishable from other structures. The carburetor consists of the main dosing tank, system, idle, transition systems, pump, econostat and idle cut off valve.

Carburetor DAAZ-4178 - technical specifications

Consider the purpose of each of the major systems of the unit. This model chosen by many car enthusiasts. Models with an index of 30 and 40 suitable for "Volga" and UAZ. The owners of these cars really respond well to such devices. They possess a wide options for customization, as well as practically hassle-free.

Main metering system

This system is designed to supply the necessary amount of fuel mixture at different operating conditions of the engine. She is able to work with all modes except idle. Thus, at medium engine loads metering system required to provide a lean fuel mixture of constant composition.

If we consider the device of a simple carb, and then look at what is the carburetor DAAZ-4178 specifications, in the simplest design, as the throttle valve is opened, the air through the diffuser is slower than the fuel is consumed, which falls into the chamber from the dispenser. Thus the mixture is enriched. In order to prevent a too rich mixture, the engineers envisaged the possibility of compensation ratio of the fuel mixture with air ratio. The number and volume of air can be adjusted with throttle valves. In carburetor units, such recovery processes represent a dosing system.

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

In most models DAAZ these methods of compensation composition of the fuel mixture are based on the pneumatic braking. Thus, fuel flows, and then sprayed not from the float chambers, and a special emulsion channel. This is a special tube. In the walls of the tube have special technological holes. It promotes the output of the air entering the top of the nozzle. There, in this channel, the process of mixing, and the mixture can escape from these holes.

As the throttle valve is opened, increasing the dilution and volume of mixture. Also increase the volume of fuel passing through the nozzles and amount of air. The amount of air fully in proportion to the volume of fuel. So compensated.adjusting the carburetor DAAZ 4178 1107010

If to speak more briefly, the GDS generates the motor all the conditions for work on small, medium, and high loads and modes. The carburetor DAAZ-4178-1107010-30 the motor provides stable power and work in all possible modes of operation.

Design and operation SHH

For the motor to idle at low speed requires only a very small volume of the mixture. In such circumstances, there is a fully closed throttle. But the level of dilution in the diffuser is now not enough to start GDS.

Here's how this carburetor DAAZ-4178-30 has in its design the system is idle. Its task is the preparation of this mixture, which allows to ensure stable operation of the engine at fully closed throttle.

The Channels the systems combine a special cavity behind the chokes and the top of the camera. When the motor is functioning at idle, under throttle, it creates a sufficiently high vacuum. When it impacts fuel is supplied from a channel to the emulsion in the channel system of the twentieth. The ratio of fuel to air in the mixture depends on the capabilities of the jets.

Next, the mixture goes for inductors, where it is then mixed with air. For this there is a technological gap between the gate and walls of the chamber. This gap can be adjusted by the screw whichinstalled on the door lever. It is the screw of quantity, with it is adjusting the carburetor DAAZ-4178-1107010.

A quantity of the mixture that passes through the channel in zaproszenie space can be adjusted with a special screw with a conical nozzle. This screw is responsible for adjusting the quality of the mixture. If to spin it, thus reducing the channel cross section.

If the throttle will open more slowly, then greatly increases the amount of air, but the fuel volume remains the same as it was. GDS still does not enter into this process due to lack of vacuum. The result of this – lean mixture and poor performance of the motor.

carburetor DAAZ 4178 1107010 30

For a smooth transition from idle to the middle mode of operation of the carburetor DAAZ-4178-1107010-40 equipped with a special transition system. It is your TV connects to the channels that are responsible for idling. There is a special hole which is made in such a way that after opening the flap she got into the zone of maximum rarefaction. This channel also receives some of the mixture in the chamber. Due to the sharp transition between modes of operation of the motor missing.

At idle when the throttle is fully closed is added to the mixture of air. Composition kompensiruet due to the presence of jets. If the screw responsible for the amount of the mixture, then the shutter will open. Increased clearance between the valve and the chamber air decreases. However, increasing the speed of the crankshaft. If you remove the screw, the frequency will decrease. On a device such as the carburetor DAAZ-4178, the adjustment is made by turning the adjustment screws.

Accelerator pump

GDS carb is designed to provide trouble-free work only with the gradual process of opening of the throttle. If you open it more sharply, the process of education is broken. In order to avoid failure in the design of a special pump. It allows you to temporarily enrich the fuel mixture if the throttle is opened sharply.

Device start

At the time of starting the engine, the crankshaft rotates at low speed. In the inlet chamber sufficiently low vacuum, and the fuel evaporates very bad at the same time. Also, if the motor is cold, the fuel vapor congenerous in the intake tract.

To make the process run more stable, it is necessary that the carburetor DAAZ-4178-40 was prepared by an over rich mixture. So, closed the choke and opened the throttle.

In Order to facilitate engine startup process, the carburetors are fitted with a special starting device. According to the principle of this air valve, and an automatic device which opens it.

Ekonostat

This device is designed to ensure that when working at maximum load to further enrich the mixture. This atomizer, which is installed at the top of the mixing chamber. Fuel ekonostat is supplied via a channel, where a fuel jet.

Economizer power modes

In order For the engine was given maximum power, the mixture must be very rich.

carburetor DAAZ 4178 1107010 40

To prepare it, the carburetor DAAZ-4178-1107010 and all other models are equipped with a so-called economizer. This system allows you to provide an additional amount of fuel that is supplied to the atomizer. But it does not pass through the main fuel jet. To enable the economizer uses a special drive.

Carburetor DAAZ-4178 at Oise

This design is more complex, unlike the factory carb. It is also a triple-emulsion type carburetor. It is an improved and more balanced the float chamber. The mixture was higher quality, the designers created a more superior channel with a swirler.

The Stable operation of the motor at startup and load here allows to provide GDS. Advanced SHH supports a more stable operation of the motor at the very possible minimum revolutions of the crankshaft. This carburetor DAAZ-4178-1107010-40 allows for a more smooth transition from idle to load.

Installation

To install this design on the UAZ, any complicated alterations would be required. However for installation you will need a thicker gasket from 126 th carb. If you install without a gasket, then there is a risk of breaking the pump drive.

Installation

How to install carburetor DAAZ-4178-1107010 for UAZ? For starters, you will need to remove the air filter and housing. Then removed a standard device. For this you need to Unscrew the studs from the manifold and replace them with the new and short. Electric valves are removed and in their place are mounted relay. Next, set the new carburetor in place of the old. Before doing this, it is necessary to stack two gaskets. Now the fitting is required to connect with a terminal fitting with a hose. Then it's time to go to the installation of the control circuit of idle econimizer.carburetor DAAZ 4178 adjustment

The last phase is adjustment of carburettor DAAZ-4178-1107010. So, with the help of special screws you can achieve optimal operation of the engine.

How to handle a jobcarb?

Though in design DAAZ-4178 slightly different from other models of the Dmitrov factory, adjustment anybody will not cause difficulties.

carburetor DAAZ 4178 specifications

In order to configure the operation of the carb, you need to use the adjustment screws that are responsible for the quality and quantity of the fuel mixture. So you can configure the mode of operation of the engine at idle. Often idle modes unstable, and without proper tuning the car will not go.

Configuration mechanism

Then we adjust the carburetor DAAZ-4178. The calibration process is a few simple steps. For a start you need to warm up the power unit. The screw is responsible for the quality of the mixture at the carb, you need to Unscrew almost completely, and then screw about 2.5 turns.

Screw responsible for the amount of fuel mixture needed to make momentum. To do this, rotate the screw until the until the revs will be about 850-950. Then with the same screw will find the highest rpm, then the other adjustment screw will return again to 900 rpm. These steps must be repeated until then, until the rotation of the screw will increase the speed of the crankshaft.

carburetor DAAZ 4178 1107010

If the speed starts to fall, then you have found the transition from a richer to lean. It remains only to tighten the screw and leave it at this point.

Now you won't have to touch the carburetor DAAZ-4178. Adjustment it finished. But it is, if when a sudden throttle transition from maximum rpm to idle was normal. If not, then you need to slowly rotate the screw.

So we found out what is the carburetor DAAZ-4178 specifications.


Article in other languages:

AR: https://tostpost.com/ar/cars/20126-daaz-4178.html

BE: https://tostpost.com/be/a-tamab-l/36082-karbyuratar-daaz-4178-tehn-chnyya-haraktarystyk-regulyavanne.html

DE: https://tostpost.com/de/autos/36271-vergaser-daaz-4178-technische-daten-und-einstellen.html

ES: https://tostpost.com/es/coches/36490-carburador-daaz-4178-especificaciones-y-ajuste-de-la.html

HI: https://tostpost.com/hi/cars/20061-daaz-4178.html

JA: https://tostpost.com/ja/cars/19775-daaz-4178.html

KK: https://tostpost.com/kk/avtomobil-der/35785-karbyurator-daaz-4178-tehnikaly-sipattamasy-zh-ne-retteu.html

PL: https://tostpost.com/pl/samochody/34208-ga-nik-daaz-4178-dane-techniczne-i-regulacja.html

PT: https://tostpost.com/pt/carros/34602-carburador-daaz-4178-especifica-es-e-regulagem.html

TR: https://tostpost.com/tr/arabalar/34672-karb-rat-r-daaz-4178-teknik-zellikleri-ve-ayarlanmas.html

UK: https://tostpost.com/uk/avtomob-l/35491-karbyurator-daaz-4178-tehn-chn-harakteristiki-regulyuvannya.html

ZH: https://tostpost.com/zh/cars/17828-daaz-4178.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

Marking lights under the xenon. Car lights

Marking lights under the xenon. Car lights

Today you can see many cars equipped with xenon optics. This is a fairly economical solution, as the xenon bulb gives a bright light. However, not many motorists are thinking about the markings on their headlamps and discussing on...

Timing belt - what is it? Why change the timing belt?

Timing belt - what is it? Why change the timing belt?

Certainly, some novice drivers do not know such a thing: timing belt - what it is, what it's for. Therefore, you should conduct a small introduction course to understand how important element in the engine it is. You should start ...

Replacing the pump VAZ-2109: price, reviews. Replacing the pump VAZ-2109 with his own hands

Replacing the pump VAZ-2109: price, reviews. Replacing the pump VAZ-2109 with his own hands

replacing the pump VAZ 2109 every 90 thousand kilometers. It is a guaranteed resource it provided that it is operated in a normal mode, and the cooling system refilled with antifreeze. The fact that antifreeze contains additives, ...

SUV

SUV "SsangYong Rexton"

Frame-based SUVs have a high security due to the more rigid body. Ssangyong Rexton - first-frame SUV in the model range of the Korean company "SsangYong". Model quite quickly gained its market share due to low prices compared to c...

Brake system VAZ-2107: diagram, device, repair

Brake system VAZ-2107: diagram, device, repair

Very important is the role of the braking system of VAZ-2107 car. With its help, the stop of the machine. The effectiveness of inhibition depends on everything. Timely stop the vehicle necessary to prevent collision or hitting an ...