Pneumatic shock absorber for car

Date:

2020-02-08 11:00:14

Views:

611

Rating:

1Like 0Dislike

Share:

Table of contents:

The air suspension is set by many manufacturers. It is structurally more complex than strut with oil or Casamassima content, but more hardy and not prone to overheating.

Suspension Components

Pneumatica consists of three elements:

  • Pneumatic shock absorber;
  • Module adjusting the air supply;
  • The compressor.

In some cars installed additional receivers in order to supply air dampers was faster and more silent.pneumatic shock absorbers

The Job of the suspension is regulated by an electronic control unit that takes readings from various sensors road pavement condition, speed, body position and driving style.

Working Principle

Pneumatic dampers adjust the position of the body, not only in moving but also when stationary.

When running in auto mode, ECU (electronic control unit) constantly adjusts the position of the vehicle based on a specified distance from the chassis to the wheels. It does not take into account the workload: the car does not SAG, if, for example, in the Luggage compartment a lot of things.pneumatic shock absorber for automobile

To Force the body height changes in a given driver parameters. While driving on the road at low speed the ground clearance is increased specifically to exclude the possibility of underbody damage. In normal mode - average speed, smooth road - the body is in the middle position. If the car is racing at high speed to improve aerodynamic characteristics of the body "squats".

From the operating conditions depends on the choice of the rigidity of pneumatic shock absorbers for the car. This quality is also regulated by the ECU.

The Process of adjustment of supply air

The air Pressure in the pneumatic shock absorber is created by the module. It either pumps it into the housing, thereby forcing the piston and lifting the suspension, or remove, the softening work of the chassis and slimming fit body.

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

In the case of the roll, for example when turning, front and rear air shock on one side will pump up more air in the shocks on the other hand - less. This ensures the stability of the machine during movement.

During off-road trips pressure adjustment in the pneumatic shock absorbers is individually for everyone: that is, the decrease or increase of air pressure can occur only in one of them.

In the static condition of the vehicle is regulated by the position not only of the body but also the suspension, which prevents premature wear of some of its elements, for example hinges of racks of the stabilizer, which experience high loads even during Parking on an uneven surface.

Air Suspension "Volkswagen Touareg"

Pneumatic shock absorbers, the VW Touareg has a classic design, but adapted to the weight of an SUV, therefore has some differences from struts for passenger cars:

  • Two receiver for the front and rear axles with increased volume;
  • Compressor with greater capacity;
  • Air springs also with a large volume of the chamber.pneumatic shock absorber vw touareg

As the load on the front spine is always more, and the design of the front of the pneumocylinders is more complicated. Unlike it has the reinforced rear dampers - vibration in the lower and in the upper part.

Pneumodampers for domestic cars

Unfortunately, the domestic manufacturer assembles the cars with air suspension, factory assembled oil filled shock set. To enhance comfort and traction, the car owners set the air dampers on the vases, which are made independently.

The basis is regular oil absorber. His stock is set pneumophila with protective rubber rings - terminal Rubena, and the whole structure is fixed with a sealant. This method is acceptable for the struts of the front suspension.pneumatic shock-absorbers VAZ

Rear shocks also improve by a spring, but instead of subset using a tubular pneumophila. It should be noted that this system is equipped with a reinforced fitting, therefore, to establish the air supply tube in it only once.pneumatic shock absorbers

When pnevmoagregata assembled and installed, it is inflated to the required height of the suspension. Then adjust the angle of the camber.

It Should be noted that too high a position of the body will lead to breakage of the cross-piece connecting drive shafts, as at a too low position the wheel will touch the bottom of the wings and body protection.

A More complicated but more functional is the design of a homemade air suspension with control. This advanced set of sensors and an electronic control unit, compressor and air springs, if you want you can add a receiver that will control minor changes in body position without the participation of the compressor.

The Cushion can be set as a standalone item or paired with the standard spring. The compressor and the receiver conveniently placed in athe trunk.

Special attention here requires the suspension calibration after installation. The adjustment should be carried out on a perfectly flat surface, to determine the position of the body first, without additional load, then at the curb. You must ensure that all the cushions were inflated evenly. And most importantly, check all connections for leaks of air. This can be done either by ear or by using a soap bubble solution.

The Disadvantage of this design is that its elements are not repairable only replace with new.

Possibility of application of pneumatic shock absorbers

The Air under pressure to replace oil not only in the suspension uprights, but in the pneumatic shock absorbers of the hood. The use of gas-lift allowed to refuse the use of a reference rod, which is needed to maintain the hood in the raised position.pneumatic shock absorbers hood

However, the design of pneumodampers requires special treatment. In winter, open the hood have much more. To shock is not out of order, it is necessary to lift the lid smoothly, without sudden movements, and pre-start the engine, giving the gas-lift to warm up. Otherwise, it may result in the destruction of their seals, which will lead to depressurization of the body.

To Install the pneumatic shock absorbers hood on any car, but you need to consider:

  • Weight bonnet;
  • Height of raising it;
  • The expected frequency of openings.

What a big load it is expected for gas-lift, the more durable they should be. Characteristics and carrying capacity of these elements is always specified in documents or on the packaging.

Press of the pneumatic spring

To Manufacture the pneumatic press of the shock with your hands is easy. It will need a shock compressor to create air pressure and the hose with the fitting for the air supply.

On the housing of the shock absorber is a preliminary markup in the place where is inserted the fitting. The hose should connect to a nipple clamp to it does not come loose under high pressure.press pneumatic shock absorber of your hands

The Fitting is inserted into the housing of the shock absorber and through the hose it connects compressor (or air pump). If the air flow the damper shaft comes into action, then press manufactured correctly. To increase the exposure area of the pressed material at the end of the rod is attached a metal disk.

This design can be made table, but also using a welded frame, transform it in a separate portable element.

How to make a homemade hot press

If the normal homemade pressing device can, for example, to bend or compress, then with the addition of a heating element there are such features as embossing or hot bonding.

To finalize the press will need the heating element - heater and two chips: one to activate the heating element, and the second to control the pressure and work stock.


Article in other languages:

AR: https://tostpost.com/ar/cars/21021-pneumatic-shock-absorber-for-car.html

BE: https://tostpost.com/be/a-tamab-l/38567-pne-matychny-amartyzatar-dlya-a-tamab-lya.html

DE: https://tostpost.com/de/autos/38149-pneumatische-sto-d-mpfer-f-r-auto.html

ES: https://tostpost.com/es/coches/37928-neum-tica-neum-tica-para-el-coche.html

HI: https://tostpost.com/hi/cars/22632-pneumatic-shock-absorber-for-car.html

JA: https://tostpost.com/ja/cars/20620-pneumatic-shock-absorber-for-car.html

KK: https://tostpost.com/kk/avtomobil-der/38975-pnevmatikaly-amortizatory-dlya-avtomobilya.html

PL: https://tostpost.com/pl/samochody/40590-pneumatyczny-amortyzator-do-samochodu.html

PT: https://tostpost.com/pt/carros/40261-pneum-tica-pneum-tica-para-o-carro.html

TR: https://tostpost.com/tr/arabalar/35453-pn-matik-amortis-r-i-in-ara.html

UK: https://tostpost.com/uk/avtomob-l/39384-pnevmatichniy-amortizator-dlya-avtomob-lya.html

ZH: https://tostpost.com/zh/cars/21838-pneumatic-shock-absorber-for-car.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

Front suspension

Front suspension "Kalina". Guidelines for repair and maintenance of "Lada Kalina"

the Front suspension on "Kalina" and "Grant" are the same. Design independent, with telescopic swivel stand, levers, longitudinal stretching and torsional stabilizer bars. The state of the front suspension affects the ride comfort...

Lineup

Lineup "Acura": description

the Acura Brand – it is a subsidiary of automaker Honda. The Japanese firm has been producing premium cars with advanced models. The brand became the first among Japanese, which could be one of the first to compete with the ...

Why pour alcohol in the gas tank? The alcohol in the gas tank to remove water of condensation

Why pour alcohol in the gas tank? The alcohol in the gas tank to remove water of condensation

Almost every more or less experienced the driver heard about the practice of using alcohol as a cleaner of the tank from the water. Given the fact that the winter cold will come very soon, excess fluid from the tank to remove just...

Heated rear seats: installation instructions

Heated rear seats: installation instructions

the Winters in our country can be very frosty. In the car it can be very cold. Do not save even included a stove. Expensive cars for that reason are available with heated seats. A budget model such functions do not have. However, ...

"Mobil motors" Moscow: reviews, services

Moscow is full of car dealerships. One of them – is “mobile motors». It exists quite a long time and has already become popular.In the showroom you can buy model cars from both domestic and foreign producers. Her...